Table HF RFID Tag Shooter TCU Board GlueLogo





  sidebar



  RFID

  FEIG RFID

  Consulting
  Publications

  About GlueLogix

 Contact:

 Larry@GlueLogix.com

 USA 919.342.0201

 GlueLogix is a registered
  trademark of GlueLogix, Inc.

  LineLogix is protected
  by US Patents 8,896,425 and 11,429,829




Home > Technologies > Feig > UHF Readers, Modules and Accessories

 FEIG UHF RFID Readers and Modules

The FEIG family of RFID devices includes modules, fixed readers, and antennas.  FEIG combines a sturdy, stable hardware design with frequently updated hardware and software.  Free software and training materials, available upon purchase, shows the capability of the readers and the low level messages needed to implement that functionality.  Development kits for C# and C++ are available under NDA.

In GlueLogix designs, FEIG technology is used to provide a consistent software interface across UHF and HF, including most standard HF protocols.  FEIG has a broad and deep offering.  The devices shown here are the most often used in GlueLogix designs for Label, Card and Plastics companies. If you need a different FEIG device, please
contact us for a quote.

Unless otherwise noted, all UHF hardware works only with UHF Gen2 chips.

Mid Range Module MRMU02

This is the bare board version of the fixed MRU02 shown below.  It has higher power and sensitivity than the MU02, and is classed by FEIG as a Medium Range reader.

Features:
  • UHF Gen2 aka. ISO18000-6C
  • Frequency range is 860-960 MHz
  • Inventories in 70 mS with one or a few tags
  • USB is Full Speed with composite device endpoints, requiring Feig DLLs for interface
  • USB connector is full size B for use with standard cables
  • RS232 is 4800 to 230400 baud
  • 6 transmit power settings:  500 mW (27 dbm) down to 50 mW (17 dbm)
  • Power consumption max. 7 W
  • CE Mark is Class 2
  • FCC ID PJMMRU102
  • 3 SMA antenna ports, software selected
  • 1 on board near field antenna, software selected
  • 12 to 24 VDC supply.  External power is required for USB.

FEIG model:

  • ID ISC.MRMU102-A UHF Reader Module (RS232-DB9S, USB-B)

Special Features:

  • Buffered Read Mode
  • Scan Mode

Caveats:

  • NOT compatible with the GlueLogix HF Reader Case!


MRMU02

Click for big view (1.2 MB)

Mid Range Fixed Reader MRU02


Features:
  • UHF Gen2 aka. ISO18000-6C
  • Frequency range is 860-960 MHz
  • Inventories in 70 mS with one or a few tags
  • USB models are Full Speed with composite device endpoints, requiring Feig DLLs for interface
  • USB connector is full size B for use with standard cables
  • 6 transmit power settings:  500 mW (27 dbm) down to 50 mW (17 dbm)
  • Power consumption max. 7 W
  • CE Mark is Class 2
  • FCC ID PJMMRU102
  • 1 SMA antenna port, software selected
  • 1 on board near field antenna, software selected
  • 12 to 24 VDC supply.  External power is required for USB.

Variants:

  • ID ISC.MRU102-USB UHF Reader (USB-B)
  • ID ISC.MRU102-PoE UHF Reader (LAN-RJ45)
  • ID ISC.MRU102-PoE-LED UHF Reader (LAN-RJ45)

Special Features:

  • Buffered Read Mode
  • Scan Mode
MRU02

Click for big view (500 KB)

Long Range Fixed Reader LRU1002

This reader is the best choice for UHF applications on presses and card personalization lines. 

Features:
  • UHF Gen2 aka. ISO18000-6C
  • Frequency range is 860-960 MHz
  • Air interface times close to best possible for UHF Gen2:
    • Inventories in 10-20 mS with one tag!
    • Read TID 12 mS unaddressed, 16 mS addressed
    • Write EPC or 8 blocks User in 60-70 mS
  • USB connector is Mini B for use with standard cables
  • USB Interface is Full Speed with composite device endpoints, requiring Feig DLLs for interface
  • 20 transmit power settings:  2000 mW (33 dbm) down to 100 mW (20 dbm)
  • Power consumption max. 18 VA
  • CE Mark is Class 2
  • FCC ID PJMLRU1002
  • 4 SMA antenna port, software selected, no speed penalty on antenna change
  • 24 VDC supply on screw terminals. NOT protected for reverse polarity. Power connector is Phoenix Contact 1714977.

Special Features:

  • Buffered Read Mode
  • Notification Mode
  • Scan Mode
LRU02

Click for big view (199 KB)
LED Summary (104 KB)
Connector Map (223 KB)

Integration Components

Contact GlueLogix


FEIG is an excellent general purpose hardware vendor.  GlueLogix is fully tooled for FEIG based projects, and can back that up with electronics and enclosure design, prototype construction, and product support. GlueLogix has been endorsed by FEIG USA as their official sales channel to Label, Card and Plastics companies in North America. GlueLogix acts as first line support for any Feig hardware or software you buy from us. We can show you how we use it, how to do the same yourself, or handle it for you.


Copyright (c) 2023, GlueLogix, Inc. All rights reserved.